softbootsurfer Posted April 16, 2019 Report Share Posted April 16, 2019 Thought perhaps a Speed analysis, as to Carving from others perspective is possible... What Speed do you have to Achieve for you to Feel you are Carving ? When I was in my Prime, maybe 10 years ago, I remember Carving Turns very slowly on the Flat, yet my Body was going almost parallel to the Snow... Does this ring a Bell for anyone else? Quote Link to comment Share on other sites More sharing options...
workshop7 Posted April 16, 2019 Report Share Posted April 16, 2019 The slowest rate with which I need to travel in order to start carving my MK and my Proteus are two very different speeds. As well, the speeds that I start to feel uneasy on each of there boards, because I’m starting to go too fast, are different. All of that being said, I have the most fun carving turns when I’m between 20 and 35 mph. 2 Quote Link to comment Share on other sites More sharing options...
bobdea Posted April 17, 2019 Report Share Posted April 17, 2019 Yup, it’s all about sidecut vs board angle vs flex vs speed. Slowest deep carves are probably gonna happen on my Kessler SL or my coiler BXFR.. the tanker will turn small too though. 1 Quote Link to comment Share on other sites More sharing options...
Corey Posted April 17, 2019 Report Share Posted April 17, 2019 Varies highly with the board and the conditions. I want enough speed to allow the board to continue to be bent in an arc through the carve by the G-force it generates. i.e. The board doesn't just ride the sidecut arc lazily - it decambers and rides a tighter arc. On something like a Donek MK that starts at around a jogging pace. On a big board that can be a fair bit faster. I generally go slower than I used to. Don't need crazy speed to get thrills any more. 3 Quote Link to comment Share on other sites More sharing options...
BlueDevil Posted April 17, 2019 Report Share Posted April 17, 2019 For me it feels best when carving at lowest possible speed. Of course that speed is higher when the slope is slower, and can be lower when the slope is faster. But lowest possible speed on which I can carve smoothly is what I'm always trying to find. 1 Quote Link to comment Share on other sites More sharing options...
big mario Posted April 17, 2019 Report Share Posted April 17, 2019 (edited) When I'm all warmed up and on my game, I like to get my big boards turning as tight and as slow as possible, between 25-35, almost stalling in my turns at times. I know the boards are riding me when I'm doing 40-50 mph, according to my trace app. mario Edited April 17, 2019 by big mario 1 Quote Link to comment Share on other sites More sharing options...
Colozeus Posted April 17, 2019 Report Share Posted April 17, 2019 what i have noticed: Soft/Stiff flex = Slower/faster speeds. At least for the smaller sub 15m sidecuts. I have yet to ride anything above 14m. 1 Quote Link to comment Share on other sites More sharing options...
Jack M Posted April 18, 2019 Report Share Posted April 18, 2019 If you don't mind some trigonometry, there is an answer: http://alpinesnowboarder.com/wp-content/uploads/2018/03/Physics-of-a-Snowboard-Carved-Turn.pdf 1 Quote Link to comment Share on other sites More sharing options...
SunSurfer Posted April 18, 2019 Report Share Posted April 18, 2019 (edited) https://doi.org/10.1139/p04-010 Or this article from the Canadian Journal of Physics. "The ideal carving equation and its applications." A key concept is that there is a maximum speed for any SCR where a carving turn can hold without skidding. The longer the SCR the higher the speed. Edited April 18, 2019 by SunSurfer 1 Quote Link to comment Share on other sites More sharing options...
softbootsurfer Posted April 18, 2019 Author Report Share Posted April 18, 2019 11 hours ago, Jack M said: If you don't mind some trigonometry, there is an answer: http://alpinesnowboarder.com/wp-content/uploads/2018/03/Physics-of-a-Snowboard-Carved-Turn.pdf I am sure this is Correct Though, I used the word Feel, because Flex plays a Major Role... We can use use any sidecut and or length you choose, isn't the Flex of the Board what allows you to use those Design parameters? No Flex, No Work at least in MHO 1 Quote Link to comment Share on other sites More sharing options...
Jack M Posted April 18, 2019 Report Share Posted April 18, 2019 5 hours ago, softbootsurfer said: I am sure this is Correct Though, I used the word Feel, because Flex plays a Major Role... We can use use any sidecut and or length you choose, isn't the Flex of the Board what allows you to use those Design parameters? No Flex, No Work at least in MHO Absolutely. The best boards achieve the perfect harmony between length, flex, and sidecut radius. I've had a board that I felt was a bit too stiff for the sidecut radius. The sidecut wanted to go shorter, the stiffness wanted to go longer. (Err... you know what I mean.) I think boards that do not achieve that harmony will not be able to "perfectly" carve with their entire effective edge length. 17 hours ago, SunSurfer said: A key concept is that there is a maximum speed for any SCR where a carving turn can hold without skidding. The longer the SCR the higher the speed. Which is basically what my article says too, among other points. (I can't get to that Canadian article without paying for it.) 1 Quote Link to comment Share on other sites More sharing options...
pow4ever Posted April 18, 2019 Report Share Posted April 18, 2019 15 hours ago, FrankNBeans said: You lost me at π r2 Going mach 5 side to side and rooster tail at the last second isn't carving? Damn it's back to the drawing board... with typical research paper: if you reach out to the author; most of the time they will send you a copy for free. Lack of no "profit sharing" and paywall for paper in academia really is doing the world a disservice. sci-hub is another "way" for the intellectual curious:https://en.wikipedia.org/wiki/Sci-Hub 1 Quote Link to comment Share on other sites More sharing options...
softbootsurfer Posted April 20, 2019 Author Report Share Posted April 20, 2019 Thanks, appreciate all your responses...enjoy the summer!! Quote Link to comment Share on other sites More sharing options...
daveo Posted April 21, 2019 Report Share Posted April 21, 2019 On 4/19/2019 at 5:09 AM, pow4ever said: sci-hub is another "way" for the intellectual curious:https://en.wikipedia.org/wiki/Sci-Hub I work/research in a fast moving industry and a lot of our stuff is published on https://arxiv.org/ (Pronounced 'archive', as in the X is a Chi [χ]) to initially publish your findings and then that can be pushed to a journal. Otherwise it can be too slow for a journal to accept and publish work whereby during that journal submission time, someone may publish your exact findings and essentially beat you to it. So it's like putting your mark on a finding. Or things that are not so novel or just something interesting can be found there. Or sometimes things are published on arxiv, which are subsequent to a journal so things like links, datasets, code etc. can be published. Orrrr things where the author may not want or need to publish in a journal- might just be something interesting or nice. If anyone is interested in any sort of technical/quantitative/sciencey disciplines, I can highly recommend taking a peek at it. You might even find something you like! 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.