Zone Posted February 17, 2010 Report Share Posted February 17, 2010 With 3+ boards, a bunch of skis from the family, skates, etc...rust is a pain in the derrière. Even after wiping the edges clean, it seems unless I leave the gear in the car on very cold days, even the cold garage produces enough condensation on cold edges to induce rust. I sometime apply car rust proofing oil on them, but am afraid it will damage the base or the board somehow. Any good tips out there, short of stainless steel (Bruce?) or titanium (Bruce with $$$)? Quote Link to comment Share on other sites More sharing options...
Sooperburd Posted February 17, 2010 Report Share Posted February 17, 2010 With 3+ boards, a bunch of skis from the family, skates, etc...rust is a pain in the derrière. Even after wiping the edges clean, it seems unless I leave the gear in the car on very cold days, even the cold garage produces enough condensation on cold edges to induce rust.I sometime apply car rust proofing oil on them, but am afraid it will damage the base or the board somehow. Any good tips out there, short of stainless steel (Bruce?) or titanium (Bruce with $$$)? You can keep the boards inside the house. Lower humidity and more constant temps will yield much less condensation. If that's not an option, I suppose you could rig up a de-humidifier box large enough to store your equipment in. I'd recommend using Damp Rid or a similar dessicant. It's cheap and available at any home improvement store. The enclosure doesn't need to be air tight to be fairly effective. Even a cardboard box large enough to fit your equipment and a bucket of the Damp Rid would probably work pretty well. Quote Link to comment Share on other sites More sharing options...
pow4ever Posted February 17, 2010 Report Share Posted February 17, 2010 I am guessing this is for winter and not for storage? I plan to use vaseline. I think ppl just leave wax on the edge for storage and it works well. As long as we keep oxygen out; it shouldn't rust. -- David Quote Link to comment Share on other sites More sharing options...
Zone Posted February 17, 2010 Author Report Share Posted February 17, 2010 I am guessing this is for winter and not for storage?I plan to use vaseline. I think ppl just leave wax on the edge for storage and it works well. As long as we keep oxygen out; it shouldn't rust. -- David Yes for winter, summer does not seem to be a problem with a waxing where I leave a coating of wax on the edges after the last run of the season. Quote Link to comment Share on other sites More sharing options...
Ronin42 Posted February 17, 2010 Report Share Posted February 17, 2010 Ti for edges maybe not such a good idea. SS could be intresting but it is probibly too brittle. How about a ipe down with some minerial oil? On sail boats they als just leave a low wattage light bulb on in the enclosed area to keep it warm enough to avoid the condensation, west marine has cool trays that hold the water from desicant. dehumidifiers are basicly small a/c units so... for longer term storage if you can compleatly cover the edges with wax then there will be little rust forming. Quote Link to comment Share on other sites More sharing options...
scrutton Posted February 17, 2010 Report Share Posted February 17, 2010 Vaseline has served me well in the humid south for garage storage. Lately though, the boards have been upgraded to inside the house, so I just let them dry naturally standing up. About the worst thing you can do is to keep them in a wet bag in a warm vehicle. Instant rust! Quote Link to comment Share on other sites More sharing options...
Sooperburd Posted February 17, 2010 Report Share Posted February 17, 2010 Ti for edges maybe not such a good idea. SS could be intresting but it is probibly too brittle.How about a ipe down with some minerial oil? On sail boats they als just leave a low wattage light bulb on in the enclosed area to keep it warm enough to avoid the condensation, west marine has cool trays that hold the water from desicant. dehumidifiers are basicly small a/c units so... for longer term storage if you can compleatly cover the edges with wax then there will be little rust forming. My old T6 has stainless edges. There are many, many alloys that are still called stainless steel, with widely varying properties. Burton seems to have found an alloy that is easy to tune, not brittle, and never rusts. I don't know why more manufacturers don't do this. Quote Link to comment Share on other sites More sharing options...
Sooperburd Posted February 17, 2010 Report Share Posted February 17, 2010 I am guessing this is for winter and not for storage?I plan to use vaseline. I think ppl just leave wax on the edge for storage and it works well. As long as we keep oxygen out; it shouldn't rust. -- David Are you sure that petroleum products aren't seeping into the porous structure of the P-tex and affecting wax absorption. The P-tex next to the edge seems especially vulnerable because it's the most abused, and tends to get the wax sucked out of it so quickly. I don't know if it'll harm the base, but I wouldn't do it to my boards until I found out for sure. I'd rather have a rusty edge (that I can clean off quickly with a gummi stone) than a base that won't absorb wax. Quote Link to comment Share on other sites More sharing options...
queequeg Posted February 17, 2010 Report Share Posted February 17, 2010 Run a block of cheap wax down the edges after riding. This will provide protection from moisture, and will come right off the instant your edge hits hard snow, so no need to scrape. Quote Link to comment Share on other sites More sharing options...
Sooperburd Posted February 17, 2010 Report Share Posted February 17, 2010 Now that's a solution, queequeg. Quote Link to comment Share on other sites More sharing options...
Donek Posted February 17, 2010 Report Share Posted February 17, 2010 We use queequeg's solution on every board we make. As we grind the board and always fail to squeegy off all the moisture rusting edges is common. The easiest solution is a stick of parafin wax in the finish area. Every edge gets a rub when grinding is finished and we don't see the rust. Quote Link to comment Share on other sites More sharing options...
Zone Posted February 17, 2010 Author Report Share Posted February 17, 2010 Thanks, that's brilliantly simple! Quote Link to comment Share on other sites More sharing options...
newcarver Posted February 17, 2010 Report Share Posted February 17, 2010 wonder if the paste type wax rubbed on the edges works too? Would be real easy to apply and coat the whole edge. Quote Link to comment Share on other sites More sharing options...
Rob Stevens Posted February 17, 2010 Report Share Posted February 17, 2010 I should probably take my boards out of the bag after the heli trip. Should be good and rusty by now... Quote Link to comment Share on other sites More sharing options...
Dave ESPI Posted February 17, 2010 Report Share Posted February 17, 2010 http://liquidlatexonline.com/solidcolorbodypaint.aspx Liquid Latex. I use 3 coats. use a foam brush on the edges for storage. It peals right off. Occasionaly I use a product called "FLUID FILM". its a deep penetrating rust inhibitor like WD-40 oil. After racing or doing a park session (courses and features are set with salt and calcium chloride at times) and ALWAYS after going home with the boards on top of a car (exposed to road salt) I rinse the boards in my shower stall and wipe them down. Adds a whole new level of "loving caress in the shower"... with your GF for a 3-some... Quote Link to comment Share on other sites More sharing options...
John Gilmour Posted February 18, 2010 Report Share Posted February 18, 2010 I use those give away chapsticks... portable and simple.. run them along your edge. done it for 20 years to some boards..no rust yet. Also..never put a wet board in a board bag or lay it on a carpet... or toss wet clothing on an edge... that rusts it within a single night. Quote Link to comment Share on other sites More sharing options...
John Gilmour Posted February 18, 2010 Report Share Posted February 18, 2010 I use those give away chapsticks... portable and simple.. run them along your edge. done it for 20 years to some boards..no rust yet. Also..never put a wet board in a board bag or lay it on a carpet... or toss wet clothing on an edge... that rusts it within a single night. Quote Link to comment Share on other sites More sharing options...
Zone Posted February 18, 2010 Author Report Share Posted February 18, 2010 I rinse the boards in my shower stall and wipe them down. Adds a whole new level of "loving caress in the shower"... with your GF for a 3-some... Sorry, we usually don't do family showers. Nice suggestion if you're at the GF stage though!:lol: Quote Link to comment Share on other sites More sharing options...
mnfusion Posted February 18, 2010 Report Share Posted February 18, 2010 I keep my boards inside, I wipe off my boards and especially the edges after I ride, I run a diamond stone over the edges before I put my board away for the day so its ready to go the next time I need it, and I have never had a problem with rust on the edges doing it this way. The only time I have ever had rust on my edges is when I would not take a board out of its snowboard bag after a day on the hill. I may be wrong but I think your problem is in how you are treating your equipment more than anything else. Keep your boards inside, don't let them 'air dry', and get them off the ground and on to a rack system and you should be fine. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.