scrapster Posted November 15, 2010 Report Share Posted November 15, 2010 Does anyone know of a readily available material that I can use to replace the base pads on a pair of Phiokka bindings? I'm thinking that a thin, high density foam sheet with adhesive on one side would do the trick. A silicone-type material might also work. Quote Link to comment Share on other sites More sharing options...
Ladia Posted November 15, 2010 Report Share Posted November 15, 2010 I used polyurethane sheet. You can get different hardness and thickness and even adhesive backing from McMaster –Carr. Pages 3130 to 3150 in their catalog. Quote Link to comment Share on other sites More sharing options...
scrapster Posted November 15, 2010 Author Report Share Posted November 15, 2010 Thanks Ladia! Lots of choices there. Did you get the solid poly (which is pretty $) or poly foam? Quote Link to comment Share on other sites More sharing options...
b0ardski Posted November 15, 2010 Report Share Posted November 15, 2010 I've done this on the cheap for my old nitros with pond liner from home depot or a garden store. A few dollars worth is enough for 2-3 pairs. Cut to fit and a little smear of all purpose adhesive like seal-all and it's better than new. Quote Link to comment Share on other sites More sharing options...
bobdea Posted November 15, 2010 Report Share Posted November 15, 2010 Does anyone know of a readily available material that I can use to replace the base pads on a pair of Phiokka bindings? I'm thinking that a thin, high density foam sheet with adhesive on one side would do the trick. A silicone-type material might also work. there's some stuff available at auto stores that is a fairly dense material that's about the same thickness and slightly softer. not sure what the intended purpose was but I used some to modify a the shoot on a field mower. my engineering was a total fail but the material was really rugged, it was basically constructed like a tire, rubber with some sort of mesh in the middle. I'd be careful using anything that could be considered foam like neoprene or something because when the air gets driven out the **** can really compress and pack out. Quote Link to comment Share on other sites More sharing options...
scrapster Posted November 15, 2010 Author Report Share Posted November 15, 2010 Hmm, I'll have to stop by the local auto store and see what they carry--as well as the pond-liner option. As for the foam, I was originally taken by the (albeit cheap) stomp pads that come with F2 and old ProFlex bindings. They're flexible but super dense foam, about 2mm thick. It reminds me of the material that used to come on the bases of the aluminum Ride softboot bindings. Quote Link to comment Share on other sites More sharing options...
heroshmero Posted November 15, 2010 Report Share Posted November 15, 2010 This site has a bunch of different makeups of plastic sheeting material. http://www.onlinemetals.com/ I am planning on ordering this 1/16 inch polypropylene to make a gasket that is missing from some bindings that I have. http://www.onlinemetals.com/merchant.cfm?pid=15650&step=4&showunits=inches&id=1154&top_cat=181 Quote Link to comment Share on other sites More sharing options...
BlueB Posted November 15, 2010 Report Share Posted November 15, 2010 I've used gasket material from automotive shops - mix of cork and rubber, very good, doesn't flex much; thin fake cutting board from Ikea is nice but creeps a bit; neoprenes come in all lot of various densities, some hardly compress at all... Dollar stores sometimes have cheap silicone hot-pot mats, or glass casters. Quote Link to comment Share on other sites More sharing options...
jacopodotti Posted November 15, 2010 Report Share Posted November 15, 2010 I use tyre tube to do that. You can take it from a perforated one at the tyres garage. Super cheap! Quote Link to comment Share on other sites More sharing options...
lowrider Posted November 15, 2010 Report Share Posted November 15, 2010 Cork silicone gasket material works great. Make sure you use ink free side down or ink will bleed onto top sheet. Quote Link to comment Share on other sites More sharing options...
Ladia Posted November 15, 2010 Report Share Posted November 15, 2010 I bought a couple 12” x 12” sheets of black and amber polyurethane 1/16” thick of various hardness. Some hardness numbers were comparable with Bomber insulating ring. I am using polyurethane under Phiokka binding and also under my workhorse TD1s. Quote Link to comment Share on other sites More sharing options...
Silver Posted November 15, 2010 Report Share Posted November 15, 2010 What Phiokka bindings are you refering to ? The PH1 or other ones? Did you find the correct hardness to keep sufficient feedback of the snow? It would be interesting that people show pictures of what they did to see the result. Thanks! Silver Quote Link to comment Share on other sites More sharing options...
Ladia Posted November 15, 2010 Report Share Posted November 15, 2010 I do not remember Phiokka model, but it was expensive piece of crap. Not happy with it and never buy another one. I do not see difference, but my sheets are only 1/16” thick. Only what is the difference soft ones are much easier to cut. Main reason for me was top sheet protection from TD1 base disks these were very roughly machined. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.