Intec Parts: $69.69. The sale from this less shipping fees will primarily form a donation to the forum.
Perfect for someone who has Intec compatible boots and F2 Race Ti bindings and is interested in trying Intec on their rear boot/binding.
All the parts needed to convert 1 binding and 1 boot to Intec Step In. My current boots are incompatible with Intec. Includes the following:
Receiver + receiver cover + pressure plate Toe plate/bail Intec heel + cable + handle All necessary bolts This would cost 190.50 (+ shipping) Canadian Loonies from yyz (if you could pro-rata buy just 1 of the required things that are sold in pairs only).
I could have wiped these down to make them a little less ugly. Perfectly functional.
Raichle 225 - size 260-265
These were my goto hardboots before I switched to Deeluxes and Backlands.
They have been used, but everything is in good working order. The heels are not worn and the buckles and zips work fine. They have not been punched. No alteration except inserts to attach a strap. Some binding marks on the toes.
Original liners (size 265) are a bit worn (cf pictures) but do the job.
I can replace them by a pair of Burton stock liners in size 270 for 10 bucks (you can have them both actually).
I also have Intec heels and BTS kit for sale on another post.
120 USD + shipping
Today I had a binding failure (Nidecker Freecarves) on my last run. My GPS watch had me above 40 mph when my back foot came loose. I slid a few hundred feet on my back but I was 100% fine, luckily. I saw that my toe piece wad sliding around and figured a screw had come loose.
I just took it apart to add loctite to each screw and was surprised to see that the offending screw had actually had a few threads sheared off. It looks like it was too short, despite coming with the bindings.
Anyone see this happen before?
SOLD - I’m selling a pair of F2 Titanflex Step-In bindings. They are size S/M. The bindings are currently configured with 6° and 3° lift blocks. I made these blocks out of Delrin when I had access to a machine shop. The wear marks on the step-in receivers are minimal, indicating the bindings have barely been used.
SOLD - The price is $175 shipped in the US via USPS priority mail.
Hate to see this one go however like all of my other boards I use them one year for race one year for training and then pass them on. This board however due to injury was only used for two races never trained and has so little use that I have never even had to polish the factory tune from F2. If you don’t know anything about F2’s Proto series it is essentially the AMG to Mercedes. By far probably the finest crafted board I’ve ever put on my feet. 9.8 out of 10 condition. Retails for nearly $2k before you pay import tax and shipping... asking $1100 fair and firm. Plus shipping
Eliminator 163:*SOLD* Used for two or three runs before dropping off for a base grind. Unfortunately a small section of the edge was ground down approximately dime thickness. Still has a lot of life left in the board as it is essentially brand new. This is one of many Eliminators that I own, with a brand new one on the way just passing along a good board and a great price. Asking $450 plus shipping
SOLD - I’m selling a pair of F2 Titanium Standard bindings, size S/M. The bindings are set flat with no toe or heel lift on either binding. It appears as though I am missing one of the mounting screws. I will dig around to see if I can find it.
SOLD - The price is $175 shipped in the US via USPS priority flat rate.
2006 Burton Fish 160 (wood veneer topsheet)
$250 shipped CONUS
N 31.6 W 25.8 T 28.6 scr 8.24 stance 20" 3" back
Bought this 3 years ago, new, in plastic, never ridden. Rode it a handful of times, not a scratch on it. Rode it at the 1st MCC powder carving event in waist deep. Really a softboot board, but worked great with soft (Raichle 313) hardboots and flexy Carve rs bindings. Really nice board for deep powder, in trees, or anywhere there's fresh snow. Super turny, surfy, with lots of taper so nose will never sink. Just okay on the groomers back to the lift.
That's wax on the bottom.
Fall season, time to clear out some gear and make room for other stuff.
I have the following bindings for sale.
Everything is in great condition and perfect working order.
All prices in USD, shipping excluded. Shipping costs to contUS via USPS should be between 8.30 (small box) and 15.05 (medium box).
=== TD2 ===
(a) Trench Digger 2, choice of blue or purple e-rings, 0 cant disks = 150 obo
(b) TD2 Second Board Kit, blue / purple e-ring, 0 cant disks = 50 obo
(c) Parts: cant disks 0 and 30 deg = 10 each
TD2 pack = a+b+c = 200 obo
=== SnowPro ===
Comes with all add-ins plus vinyl struts to prevent the space between the disks and the board to suck in the inserts of your board (the only real flaw of these otherwise very performant bindings).
Asking price 100 obo.
=== F2 Intec Stepin ===
These are not the last generation, but have been gently used. The set comes with Raichle step-in heels and cables.
1997 Burton Performance plates for sale
The bindings have a ¼" aluminum plate underneath the plastic
The toe blocks have a stainless steel plate underneath and are held with stainless steel rivets
The bails are 5 mm stainless steel
Tool-less size adjustment
- two pair of soft (red) and two pair of hard (blue) shock absorbers
- two 4x4 and two 3D disks
- one 4x4 offset disk (for canting plate)
- two 4x4 aluminum disks (very rare)
- two 7° canting plates with two 4x4 and two 3D inserts
- leash (with homemade stopper)
- all mounting hardware
Buyer pays shipping from Montreal, QC, Canada
Selling because I'm getting out of the sport
No registered users viewing this page.