mikel45 Posted February 2, 2010 Report Share Posted February 2, 2010 Hello all, new to the sport, contemplating using my Raichle Flexon Comp boots, interested in learning what modifications to the boot should be considered – any suggestions? As always, then ... CHEERS! Quote Link to comment Share on other sites More sharing options...
Kent Posted February 2, 2010 Report Share Posted February 2, 2010 I wouldn't recommend it....and it really depends on your total set-up. But, generally speaking "back in the day", the mods were: - routing the cant mec to an oval shape to allow slight lateral movement - increase forward lean shin in rear foot - shave off slight material on side "tongues" (it's an open throat design boot) None of those make a huge difference. Quote Link to comment Share on other sites More sharing options...
queequeg Posted February 2, 2010 Report Share Posted February 2, 2010 Hello all, new to the sport, contemplating using my Raichle Flexon Comp boots, interested in learning what modifications to the boot should be considered – any suggestions? As always, then ... CHEERS! Starting out on ski boots? You can do it, but you will be putting yourself at a pretty huge disadvantage. Quote Link to comment Share on other sites More sharing options...
tex1230 Posted February 2, 2010 Report Share Posted February 2, 2010 I wouldn't recommend it....and it really depends on your total set-up.But, generally speaking "back in the day", the mods were: - routing the cant mec to an oval shape to allow slight lateral movement - increase forward lean shin in rear foot - shave off slight material on side "tongues" (it's an open throat design boot) None of those make a huge difference. We also used to cut a V into the calf of the boot and add a better (wider) power strap. If you do this cut, be sure to round off all the edges. you can ride in these fine, especially if you have softer tongues - but as stated above if your goal is freecarving you'll want to transition to snowboard specific boots when you have a chance. Quote Link to comment Share on other sites More sharing options...
Keyser Soze Posted February 2, 2010 Report Share Posted February 2, 2010 Someone had recommended the FTs/Flexons not long ago when I was doing some research, here's what he said: Can't go wrong with full tilts/flexons. There is a HUGE range of adjustment in the tounges....probably from around a 60 flex index to around 120 or so. There's also the option of running different flexes on each boot, swaping around, etc. Other bonuses: - Light, very light. - Good lateral and aft stiffness. But you could take a rear cuff peice and soften it if needed (and swap it in and out) - Very modular parts - Wide canting range. - Most importantly, the tounges provide a VERY linear progression of the boot stiffness. It's like flexing against a spring. Some overlap boots can be soft for a while then get stiff quickly, which can't be good for edge control. The guy in the pics above looks like he's running the stiffest black tounge, which still flexes nice. But you could freeride on a softer tounge. - Flexons on ebay for cheap (for spare parts) Oh on the liners - a tounge type liner will usually be stiffer than an intuition/thermoflex. Quote Link to comment Share on other sites More sharing options...
bobbeck Posted February 3, 2010 Report Share Posted February 3, 2010 I bought some FT boots this year off ebay for 108.00. With a little heel lift the boots fit really great, they have the intuition liner. I was thinking why not pair them up with Fins new "sidewinders" to provide lateral flex. I,ve got the jibbers super soft tongue and flex seems close to my AF 600 boots with blue spring BTS. I'd try the Flexons for sure. Bob Quote Link to comment Share on other sites More sharing options...
kipstar Posted February 3, 2010 Report Share Posted February 3, 2010 One positive is the sole doesn't flex like the snowboard boots do so you get a nice stiffness; however it is also quite long as well which is a negative when I switched the sole length definitely reduced quite a bit for the same 27.5 size boot. On any board narrower than about 200mm, this starts to have an impact. I am a little surprised, as I am quite sure switching from riachle flexon comps to the raichle indys was a drop in weight; the flexons I used to use were mighty heavy compared to the new snowboard boots. Quote Link to comment Share on other sites More sharing options...
tex1230 Posted February 3, 2010 Report Share Posted February 3, 2010 one more note - when we raced in the flexons, we would dremel the toe and heel to give a little more clearance - but it does make them useless for skiing. Quote Link to comment Share on other sites More sharing options...
P06781 Posted February 4, 2010 Report Share Posted February 4, 2010 I dremeled the toe and heels and took the tongue off . Then grind off the tongue near the ankle areas to soften up the flex . I loved my flexons ! Jim Quote Link to comment Share on other sites More sharing options...
DiveBomber Posted February 4, 2010 Report Share Posted February 4, 2010 ive always contemplated getting the kryptons or full tilt boots but after hearing all the mods and then the problems, IE boots breaking etc, I have to ask, why? Quote Link to comment Share on other sites More sharing options...
kipstar Posted February 4, 2010 Report Share Posted February 4, 2010 Divebomber, the question why is very exstisential or however you write that. ;_) Quote Link to comment Share on other sites More sharing options...
mikel45 Posted February 4, 2010 Author Report Share Posted February 4, 2010 To all (Alpine Ace, Trench Digger, Lord of the Ruts, Groomer Grommet, Carver Extraordinaire) ..... mucho gracias ..... though to be honest, me missin havin' the heart to actually dremel my Raichle's. Decided mods for now: 1) looking into replacement tongues for added flex option(s), presently have the rather still "racing flex"; 2) the comps came with three different options for liners: a standard liner, a Thermofit liner, or a Thermoflex liner. Contemplating adding footbed and upgrading to heat moldable liner from the existing Thermofit liner. Though I do like the attached velco power strap; 3) Concerned about the boot/binding interface. Any suggestions for replacement toe and heel pieces? Interestingly enough, some have experimented with attaching "vibram" hiking soles. Quote Link to comment Share on other sites More sharing options...
P06781 Posted February 4, 2010 Report Share Posted February 4, 2010 Use a bench grinder to slowly remove material here to soften the flex. Jim Quote Link to comment Share on other sites More sharing options...
mikel45 Posted March 2, 2010 Author Report Share Posted March 2, 2010 if your goal is freecarving you'll want to transition to snowboard specific boots when you have a chance. Flexon mod suggestions greatly appreciated. Decided to take advice, went ahead and purchased hardboots. Surprisely inexpensive when purchased used. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.