everts72

Seems court decided: Rok Marguč on Facebook: In the end, the truth always wins. Allflex was lying about me in public. They should remove everything about me in 15 days. They also lied about the patent. The Slovenian court said they did not have a patent for snowboard plates. It was hardely patented plates in 2007, which we developed together in 2010. They will pay a lot because they were lying. We won today. The truth always wins. IronRock #rockyourboard

Rok was only rider with Allflex, because he and Aco developed and tested this plate from zero to this point where it is now. Later when other riders started to use Allflex had Aco and Rok some misunderstanding I would say. And now we are here.... Allflex vs Iron Rok.

Hello guys, yes I tried this new models of Ballistic (but prototypes) in different stiffness (also with Allflex). It's was really nice board, but problem was that it was only 19cm wide in the middle, so I had some problems with hanging out with my boots (deeluxe 319mm). On this specifications seems they went on 19,7cm. It can't be found on their web page because I've heard they stopped with alpine production.

http://www.carver.si they have worldwide shipping

Živjo, škoda, da si zamudil sešen 2 tedna nazaj na Cerknem. Je bilo kar neki opreme za sprobat. Če želiš ti lahko jaz kaj pomagam, pošlji mi pm. lp

Original instructions from Palau: Dear PALAU Customer, Thank you for purchasing the thermoformable liner. We recommend that you carefully read the following instructions to use this product in the best conditions. The thermoformable PALAU liners are preformed and must be used without additional accessories. Along the time, they’ll adapt to the shape of your foot and become more comfortable with each use. Anyway, in order to achieve the best fitting, we recommend that you mold it by yourself or by a professional boot-fitter. THERMOFORMING INSTRUCTIONS For best results, follow these steps. - Use a convection oven (hot air) which has been preheated to 110 ° C. - Place in oven preheated between 5 - 8 min according to the material and thickness of the liner (1 min / mm thickness approx) until they are soft and malleable. - Make sure the shell of the boot is completely unbuckled and at ambient temperature. - Put a foot-bed under your foot and place a toecap over the toes (these caps should be used to create space in the toe box; humidified cotton wool might be ok). Finally, pull a thin sock over the prepared foot. Two different method inserting liner in the shell: Work quickly so that the foam does not cool and does not lose its molding properties. 1) Remove liner from the oven and put it in the foot. Make sure that the under foot seam is straight and that the ankle reinforcements are even. Crossing Overlap flap outer liner with internal flap. The external reinforcements material on outside. Slide the foot and the liner inside the shell with one hand at the heels to guide smoothly. Be careful not twisting or folding the liner during process (help yourself with a shoe horn or a piece of cardboard). 2) Remove liner from the oven and put it carefully into the shell. Check that there are no folds or twists and insert your foot in it. Make sure the heels are positioned at the bottom of the shoe by gently kicking the back of the shell and adjust the external and internal flaps around the shin. The flaps should pass under the plastic shell. For central tongues liners, be sure to place it in the center, and pull them up if necessary. Close the buckles about half of their ability and hold a slight flexion for 10 minutes while the liner cools. Once the liner has cooled, remove the foot and the liner of the shell, take of the socks and toes caps and place foot bed inside the liner. If folds or twisting, it can be remolded according to the instructions mentioned above. 2 times max. The liners must be removed from the shell after skiing. Dry the liners away from direct heat. Washable in cold water with mild detergent. Let dry them completely before use.

Looking for a Northwave .950 B shell size (25.5 mp) for a friend. everts72 at gmail.com cheers, M

Some photos: http://s23.postimg.org/f8mgumftn/IMG_20160131_213745.jpg http://s12.postimg.org/jj3uaz74d/IMG_20160131_213754.jpg http://s7.postimg.org/elpjl7463/IMG_20160131_213843.jpg New price: 500eur+ shipping, also possible with MK GS plate

For sale Oxess snowboard GS 185cm, 19m radius. Black carbon top. Like NEW , price 550 € + shipping from Slovenia (EU) more info: jernejrozman@gmail.com

:)

Try here: http://carver.si/snowboard_cevlji/PALAU_liners

Artice Extreme Carving Team new board porn for this season- Plasma Snowboards www.facebook.com/CarvingTeam All boards are Competition model: 2x 184cm/20cm waist--> new shape 1x 184/18 2x 190/20 We tried boards last season and must say they are amazing carving machines with great performances. If you have chance I recommend to try it

I know it's not from person who makes allflex plates, that is why I'm asking who made it. hope new owner will have fun with plates

Never saw this plates on our slopes. Who made it?

And his backside on first photo