Bora20 Posted April 28, 2010 Report Share Posted April 28, 2010 I bought a pair of SnowPro Race LTD Step-in bindings from Dan Yoja http://www.upzboots.com/ on sunday night and they arrived today. After speaking with Dan, he felt that they would offer the convenience and flex that I want in an all-mountain setup. Further discussions with other BOL members convinced me to try them, plus they are hard to beat at their price point. They are also designed to work with the UPZ boots perfectly, so that made it easy too. The bindings aren't as easy to setup as the Bombers, but also don't require different cant plates for lift. Everything is included and the instructions are quite clear. The heels and t-nut hardware are also included, which again saves on cost. I set everything up in my kitchen, on the boots and on the board. Angles are easy to setup as is the amount of lift/cant required. The rear binding comes with a handle, which can be replaced with the small included handle like the front if desired. I will have to wait until next winter to test it all out, but it won't be long before it snows again soon. Bindings and parts included Front foot, toe lift, no cant Rear foot, heel lift, inward cant Installed at 45/40. No hangover on front foot, rear has some. Quote Link to comment Share on other sites More sharing options...
Petrol Posted April 28, 2010 Report Share Posted April 28, 2010 I like the look of release much better then the pant cuff bunched up over the Intec handle look.... Quote Link to comment Share on other sites More sharing options...
Bora20 Posted April 29, 2010 Author Report Share Posted April 29, 2010 The bindings come with 1 long handle and 2 short handles. I am going to find out if I can get another long handle for the front binding as well. Quote Link to comment Share on other sites More sharing options...
Miltie Posted May 4, 2010 Report Share Posted May 4, 2010 Bora, I am long time Bomber fan and normally ride TD bindings due to the reliability. A few years ago I picked up some of the standard bail SnowPro Race bindings for a smoking deal to use on my stash of boards in LA. My weight is about 160 lbs and my riding skill is average. After a few hours of riding, the 4 mounting screws on the plastic center disks tend to lose torque. Even had a binding shift 30 degrees while riding. I think this is mainly a function of the plastic material used. You will want to keep a #3 Driver in your pocket and check those mounting screws a few times during your day on the hill. Enjoy your new set-up! Tom Quote Link to comment Share on other sites More sharing options...
Bora20 Posted May 4, 2010 Author Report Share Posted May 4, 2010 Bora, I am long time Bomber fan and normally ride TD bindings due to the reliability. A few years ago I picked up some of the standard bail SnowPro Race bindings for a smoking deal to use on my stash of boards in LA. My weight is about 160 lbs and my riding skill is average. After a few hours of riding, the 4 mounting screws on the plastic center disks tend to lose torque. Even had a binding shift 30 degrees while riding. I think this is mainly a function of the plastic material used. You will want to keep a #3 Driver in your pocket and check those mounting screws a few times during your day on the hill. Enjoy your new set-up! Tom Thanks for the tip Tom. I have a small screwdriver set that fits in your pocket and is round everywhere so I won't be stabbed. I will tighten everything up on the hill when it is cold so that it stays tight. Quote Link to comment Share on other sites More sharing options...
BlueB Posted May 4, 2010 Report Share Posted May 4, 2010 Another Snowpro trick is to wet-mount the bindings. It would create such a sticky effect (on gloss top boards) that it will never rotate. You'll actually struggle to get the gasket off the board. But yes, definitelly tighten up everything in the cold. Quote Link to comment Share on other sites More sharing options...
mattj Posted May 14, 2010 Report Share Posted May 14, 2010 I have a pair of these but I went back to the standard toe clip after popping out of them a few times. Really make sure that you are clipped in and that it is nice and solid before heading down the hill. I found that a short phillips head screwdriver made a good ice pick and was also useful for binding tweaks on the mountain. Getting ice out of the holes in the boot heels is annoying! Matt Quote Link to comment Share on other sites More sharing options...
Bora20 Posted November 21, 2010 Author Report Share Posted November 21, 2010 I used them today on the Dynastar 166 today. They worked great and I put changed them so the front binding had inward cant. Step, click, step click, easy as pie. No spinning, but you can't turn them less than 18 degrees. This isn't a huge deal, but something to note. I was running them at F30/R25 and needed to add a bit more front angle. I didn't notice anything wrong or right with them in my short time on them, so I will take that as a very good thing. Quote Link to comment Share on other sites More sharing options...
Bora20 Posted December 4, 2010 Author Report Share Posted December 4, 2010 I used the bindings today on my Prior 4WD. After the last day I checked them and they were coming loose. I have loctited everything in place and there were no issues today. They do offer a bit of side-to-side flex in them, which is unlike my TD2s. I assume that they are similar to the TD3 Sidewinders. Nothing broke today under my 215 lbs frame. Settings: F - 50 degrees with 3 degrees inward cant R - 47 degrees with 3 degrees inward cant and full heel lift I did get a total of 12 miles of riding in today before my feet, lungs, and thighs were burning. You know that feeling when you almost throw up the yogurt you have 2 hrs before for breakfast? Well that is the trigger to tell you that it is time to stop and spend more time in the gym. Quote Link to comment Share on other sites More sharing options...
Bora20 Posted December 13, 2010 Author Report Share Posted December 13, 2010 I have since changed the settings on the bindings to try and get rid of my front leg burn. If both legs burn that is good, but just the front means something must be off. F - 50 degrees with 0 degrees inward cant, no heel lift, full height toe pad. R - 47 degrees with 3 degrees inward cant, no heel lift, low height toe pad. This should force a bit more weight back to the rear leg. I also centered the bindings on the board's effective edge to see what kind of feel that gives. Quote Link to comment Share on other sites More sharing options...
Bora20 Posted January 18, 2011 Author Report Share Posted January 18, 2011 I will be adding the heel lift back to the rear leg. I think I finally have everything setup correctly and carving is starting to come more naturally. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.