[Burton Coil 165]

SOLD. Thanks Tom.

[Burton Coil 165]

Hi gigo60 - I just emailed you. Thanks. Ian

[Burton Coil 165]

Hi All -

I have a slightly used Burton Coil 165 in great shape that I no longer use. It has maybe 15 days on it. Top sheet is super clean. Bottom is in good shape. Biggest gouge in the base is maybe 2cm long by 5mm wide by 2mm deep. The edges need a quick tune and it could use a wax; other than that, this thing's barely broken in.

Asking $150 + shipping or best offer.

Thanks for looking.

[Madd 158]

Hi - Just checking to see if the board is still available. Any significant defects? I'm not familiar with this one...anything in particular you might compare it to?

Thanks a lot - Ian

[Soft Boots - MP 28 - 28.5]

Hey Sandy -

The boots got here today, look great and fit awesome! I can't wait to ride them this week.....

Thanks again - Ian

[Soft Boots - MP 28 - 28.5]

Hi Sandy - Check your email, the money has been sent.

Thanks again! - Ian

[Soft Boots - MP 28 - 28.5]

Hey Sandy - Sounds great. Is the $15 for priority shipping? If not, I can throw in a few bucks more to get them here quicker (the gel ankle inserts in my '97 Heelside boots have finally shriveled and they hurt like hell). Can you send the paypal request for $140 (or however more for the shipping) out to:

madmax409@hotmail.com

Thanks a lot, I really appreciate it.

- Ian

[Soft Boots - MP 28 - 28.5]

Hi Sandy - That is an awesome deal. Are the K2 liners 28.5 also? What's the difference between them and the Driver X liners as far as fit / boot feel goes?

Also, how much to ship to 12037?

Thanks a lot - Ian

[Soft Boots - MP 28 - 28.5]

bump...

[CATEK OC2 's]

Thanks ZetaTre.

[Soft Boots - MP 28 - 28.5]

I'm looking for some stiff soft boots like Burton Driver X or Salomon Malamute. My foot measures just a hair over 28cm so a size 28 or 28.5 should work. My budget is around $125. Thanks

[CATEK OC2 's]

sorry for the wait.....I'm hoping to hear from the other guy sometime tomorrow. thanks for your patience

[CATEK OC2 's]

Hi ZetaTre - No email came through. Thanks - Ian

[CATEK OC2 's]

Anyone?

[CATEK OC2 's]

Bump.

[CATEK OC2 's]

Bump.

[CATEK OC2 's]

I really need to move these out...........just listed them on ebay.

Thanks for looking.

By the way, how do you edit the original post title? I can't figure out how to fix the "OC2".

[CATEK OC2 's]

Catek OS2 's that I bought used last season. I used them maybe a dozen times so they're in virtually the same condition I bought them in. The following information is from the Catek website:

Standard | Step-In

We offer the OS2 bindings in Standard or INTEC-compatible Step-In (SI) versions. The choice between the interfaces is mostly an issue of personal preference, but there are a few general differences. The SI system is more rigid than the bail closures, particularly in regard to lateral movement, and requires that you install INTEC heel units on your boots. The bail/toe lever Standard system accomodates a wider range of boots, including ski boots and older, non-INTEC compatible boots. Our snug, contoured heel bail offers the best boot fit available.

Short | Long Plates

The Short Plate is ideal for smaller boot sizes (<10US) and lighter (<180lbs) riders. The 3/8" thickness provides a more forgiving ride than the long plate. The Long Plate accepts all boot sizes (up to 31.5MP, depending on the boot), and its 1/2" thickness provides the most powerful ride on the market. Riders weighing more than 180lbs or with a boot size greater than 10US must use the long plate.

They are step-in's with short plates.

Overall, the bindings are in great condition. There are a couple of small scratches and there is a small amount of wear on the heel receivers. I used Intec heels and everything felt nice and tight.

As for the hardware, the front binding has a short kingpin and the rear has a long kingpin. They came with no spacers so I just bought some stainless washers which worked fine (1 in the front and 3 in the rear). There are only 3 screws for attaching each disc (they are combo discs that can be used with the Burton 3D system or the standard 4x4 pattern) to the board which worked fine for me on my Burton 3D set-up........you'll need 2 more screws if your board has a 4x4 pattern. All 4 o-rings are there and the elastomers are in good condition.

$150 includes shipping to the lower 48. Anything else, let me know.

Thanks

[Raichle 224 with Intec MP 27]

Skrekk - RJ came through and got the boots. Good luck finding some boots that work well for you.

Thanks RJ. - Ian

[Raichle 224 with Intec MP 27]

Hi RJ - I just sent you some mail. Thanks - Ian

[Raichle 224 with Intec MP 27]

Hi Skrekk - I'm waiting to hear back from RJ. As soon as he lets me know if he's going to take them I'll let you know. Thanks - Ian

[Raichle 224 with Intec MP 27]

Hi RJ - I sent you an email. Boots are available. thanks - Ian

[Raichle 224 with Intec MP 27]

I bought these boots on BOL last season and used them 6 times; I need to part ways with them and I'm hoping to get my money back out of them.

The sole length is 295mm, the stamp on the inside of the upper shell and tongue is 25 - 27.5, the stamp on the inside of the lower shell is 27 - 27.5, the liner is a 27. For what it's worth, I wear a street shoe size 10 or 10.5 and my MP is a 28. These boots, at a MP 27, are a bit tight and uncomfortable when cold; 5 minutes in, they warm up and fit perfect.

Not sure of their age. Overall they're in good condition, everything works very well. Intec heels work great.

SOLD - Thanks RJ

[BX Board, Bindings, TD3 E-Rings]

Hey Mike - I just sent an email. Let me know if it didn't come through.

Thanks - Ian

[BX Board, Bindings, TD3 E-Rings]

MikeC - I definitely don't want to cut line......let me know if you want to ship it my way and I'll buy it whenever you want.

Thanks - Ian