Intec Parts: $69.69. The sale from this less shipping fees will primarily form a donation to the forum.
Perfect for someone who has Intec compatible boots and F2 Race Ti bindings and is interested in trying Intec on their rear boot/binding.
All the parts needed to convert 1 binding and 1 boot to Intec Step In. My current boots are incompatible with Intec. Includes the following:
Receiver + receiver cover + pressure plate Toe plate/bail Intec heel + cable + handle All necessary bolts This would cost 190.50 (+ shipping) Canadian Loonies from yyz (if you could pro-rata buy just 1 of the required things that are sold in pairs only).
I could have wiped these down to make them a little less ugly. Perfectly functional.
By Jack M
Outstanding board, used about 15 days. Selling because it's a little too close to my latest custom 180, and the wife says I need to clean out the closet!
10-14m KST sidecut. 20.5cm waist. 48-58cm stance width range. Similar turn shape as a 168, just 2m longer radius range, and 6cm longer length. That is to say, this is not a straight-tail racer, but a great freecarver that will finish the turn. Very exciting ride. Swiss hand-made for me at 185lbs in May 2018. Factory thumbprint base grind. Factory edge bevels at 2 side, 0.8 base. Base has not been ground, edges have only been touched up with a diamond stone. Will wax before shipping. Superficial base scratches only. P-tex topsheet condition is very good. No damage. I have about $1800 into it after import tax and shipping. Letting go for $1250 shipped to the 48 states. I will pay the first $50 for shipping elsewhere. Satisfaction guaranteed.
By Denis Lafrance
SOLD---------------COILER STUBBY V2, 2019 , 175 LONG 20 CM WIDE 13/14m SIDECUT
Bought the board brand new in 2019 with magnificent snakeskin deco with top carbonium, base look as it was new, no scratch or dig. Its short overall length with comparatively long effective combined with a moderately speedy sidecut is a potent combo for all around fun. It's a super fun ride which can handle a lot of your daily carving duties. If you want to carve while dragging your elbow in the snow this is your board. Really look like a brand new board.
595$ + shipping
SOLD - I’m selling a pair of F2 Titanflex Step-In bindings. They are size S/M. The bindings are currently configured with 6° and 3° lift blocks. I made these blocks out of Delrin when I had access to a machine shop. The wear marks on the step-in receivers are minimal, indicating the bindings have barely been used.
SOLD - The price is $175 shipped in the US via USPS priority mail.
Hate to see this one go however like all of my other boards I use them one year for race one year for training and then pass them on. This board however due to injury was only used for two races never trained and has so little use that I have never even had to polish the factory tune from F2. If you don’t know anything about F2’s Proto series it is essentially the AMG to Mercedes. By far probably the finest crafted board I’ve ever put on my feet. 9.8 out of 10 condition. Retails for nearly $2k before you pay import tax and shipping... asking $1100 fair and firm. Plus shipping
Eliminator 163:*SOLD* Used for two or three runs before dropping off for a base grind. Unfortunately a small section of the edge was ground down approximately dime thickness. Still has a lot of life left in the board as it is essentially brand new. This is one of many Eliminators that I own, with a brand new one on the way just passing along a good board and a great price. Asking $450 plus shipping
SOLD - I’m selling a pair of F2 Titanium Standard bindings, size S/M. The bindings are set flat with no toe or heel lift on either binding. It appears as though I am missing one of the mounting screws. I will dig around to see if I can find it.
SOLD - The price is $175 shipped in the US via USPS priority flat rate.
By Jack M
Bought this 2019 F2 World Cup SL 163 on clearance from @i-carve.com for the director of CVA snowboarding. Took it out yesterday to see how it is. VERY impressed!! Edge hold, smooth, air between carves, perfect flex, great turn size. Tight enough to only use half the trail, but not so tight that you're making 1000 turns in a run. F2 is back on my radar! Hadn't been on one since SES 05. A friend who loves F2 tells me they were the ones who made the "Made in Austria" Kesslers. Based on the top shelf build quality I'd say it certainly seems possible. Don't worry, this pic is low on the mountain, there's more snow up higher. But we are off to a bad start here in the east. Hoping for a big dump tonight.
Up for sale is a race-ready Kessler GS 185
50cm stance width, UPM and Vist center mounts as well
Condition is nearly new. It's only been ridden a few times and I'm selling because it is simply to stiff for me at 155lbs and my infrequent riding these day. It probably rides great at 180-220lbs. Small scuffs from a plate and some lift rash but otherwise both the top and base are in great shape (base wax on there now). Edges are razor sharp and have all of their life left.
No registered users viewing this page.