EastCoast

Originally Posted by *Ace*1. Mark Brown, M-F 2. Jim Cheen, W-F 3-4. Andrea, Dave & Lillian Morgan, M-F 5. GeoffV, M-F 6. Michael Mercurio, M-F 7. Stephane Paquette, M-F 8. Derek Bonser, M-F 9. Tabatha, M-F 10. Brad Burns, M-F 11. Annie Beaudoin, M-F 12. Claude Fagnan, M-F 13. CarveFather, W-F hopefully 14. Bob Russell Buggs, W-F 15. Alex Juhasz, M-F 16. Steph Juhasz, M-F 17. Karson Mui, W-F 18. John Philkill, M-S 19. Hilux, M-F 20. Fishrising W-F 21. Shaggy 22. Ian M, M-F! 23. Max L, M-F 23. Tim K, M-F 24 Murphy Tues-Fri 25. Brian Barrett, W-F (or more 26. Khanh Vu M-F 27. Rob A Tue-Fri 28. Tom A Wed-Fri 29. Redhawk Wed-Fri 30. Jack Michaud Thu-Fri 31. Glenn Mon- Sat. 32. *Ace*, W-Thu. 33. Phil MacAulay, M-F

Looking for a Madd BX, good shape, good edges. If you have one you will part with let me know. thx, Phil.

Hi, I have a pair of sidewinders but would also like an extra set of toe and heel assemblies to mount directly on a plate. I asked Bomber if they would sell separately and no go. So, if you have a set you don't like (I don't need the rest of the binding) maybe you bought a set of sidewinders and would prefer just the standard TD3 setup, let me know and I will take them off your hands. thanks, Phil.

The buyer for the 190 backed out, will sell for 150.00 plus shipping. Beetle3 if you are still interested you have first refusal, let me know.

Hey All, anyone have a set of yellow TD3 E-rings they are not using and want to part with? May be simpler just to buy new, but if anyone has a set lying around, recycle and reuse. New cost is about $29, so I'll pay say $23 plus shipping for a pristine set. Also looking for a 3 degree base plate, or maybe a full second board kit. thanks, Phil. philupm@hotmail.com

Boots board and bindings are sold, Thanks. Phil.

Price Drop, Rossi 190 for $190 Surely someone wants this board for a reasonable price.

Boots gone, bindings pending Rossi price drop to $210 Phil philupm@hotmail.com

East Coast Gear to sell or trade: 1) 26-26.5 UPZ Boots. I assume they are 26.5 (they do not say anywhere, inside the base part of the boot says 7-8 and upper says 8-9.5). They are the right length to fit me and I take 26.5 Deelux. These are used but have had minimal use. I bought them last year on this site to try, but I don't like the fit (I'll stick with my AF600s). No footbeds, and boots are missing one buckle multi-position piece, not the buckle itself, small part and most ski shops could supply a replacement (I'll check to see if I can get one myself). Sole plates have t-nuts, $150.00 2) One pair Snow-pro Fast step-ins (short plate up to size 26.5) + 1 Snow-pro race thrown in. Step-ins have had minimal use, single race plate is well used, might be useful as a front binder, or parts. Step-ins have had minor modification (removal of a bit of plastic inside along the cable guides that guide the cables used to withdraw the pins, this does not effect the strength of the binding in any way) to permit greater (1-2 mm) heel-pin insertion into heel receivers. This decreases the likely-hood of unintended release and snow clogging. I did this because when I bought the bindings I noticed that the far pin on both bindings did not insert as far as the close pin. When I took the bindings apart I say that the cables were a bit to tight on the far side so I modified the guides to provide a bit more slack. Comes with cant and lift plates and hardware. Best for a lighter rider with 26 or smaller boots. $65.00 or trade as above. 3) Rossi World cup 190. New, still in plastic. Although I presently ride a medium flex Donek Blade 180 (SC 13 m), I only weight 165 and I have never had the guts to ride this board on the hard, crowded, narrow runs of East Coast Canada. Board specs, 234 mm tip, 190 waist, 230 tail, and it is stiff (side cut radius? 14-15 meters? I am not sure) Sell for $250.00, or trade as below. (or for any of above, trade or part trade for 26.5 Deelux, or new/good shape thermo-fit liners to fit 26.5 AF600's, or used TD3s, or 10-12 m radius 170-180 board (what do you have?) I also have a Donek 180 FC II, stiff flex, nice condition, no damage, that I got used but has not been used much, a bit too stiff for me, that I might trade or sell. I am located in Halifax, Nova Scotia. philupm@hotmail.com

Hi, I am interested in your EC 175. Where are you located? My email is philupm@hotmail.com thanks, Phil.

the title says it all, contact me if others do not come through, philupm@hotmail.com thanks, Phil.

Hi I am interested in the boots if you will split up the gear. pls contact: philupm@hotmail.com thx, Phil.

Hi, in the past I have bought td1's for $75, but have seen them go for significantly more, up to $120-130. I use the bails and bail plates on bindings of my own design. I already have 2 sets, but could use spares. So for me at this point paying the high end doesn't make sense, but I could offer you say 180.00 for both. Phil

How much are you looking for? got any pics? thanks, Phil.

Hi, I hope this post is ok here now that this board seems to be sold. I have the same board, new, still in plastic, never used. I got it a year or so ago from a friend who never used it. I also have never had the opportunity (or the goolies) to ride a 190 19 m sidecut on the hills where I live. Besides, I have moved to EC style and now ride a 180 Donek Blade, thats more than enough length for me. So, new, still in plastic, no base work or edge work done on it. However, there are a few small spots of surface rust in a couple of places on the edges from storage. These were there when I got it. Minor, a very basic tune-up and they will be gone. Would like to get $200. Buyer pays shipping. I reside in Canada, Nova Scotia. contact: philupm@hotmail.com